LADISCH CORPORATION, INC.

Location: 1233 Water Street East Greenville, PA 18041

Online Bidding Ended:

Auction Highlights

LATHES

40” X 120” American Mdl. 36 Lathe, taper attachment, 9-400 RPM, 12-spindle speeds, [3] roller bearing steady rests, 32” 4-jaw chuck, S/N: 65463-43

20” x 126” Monarch Mdl. 1610-13TX126 Lathe, 145-1500 RPM, Camloc spindle, steady rest, roller bearing steady rest, 16” 3-jaw chuck, S/N: 46089


WELDING POSITIONERS

18,000# Aronson Mdl. GE180A Welding Positioner, vari-speed, 84” square table, S/N: 7584

 

SAWS (all types)

9” x 16” DoAll Mdl. C-916S Horizontal Bandsaw, 1” blade, 2HP, pneumatic clamp, S/N: 482-92312

14” Everett Industrial Mdl. 14/16 Abrasive Cutoff Saw, 7.5HP, S/N: 7493

Craftsman 10” Tilting Arbor Saw

Craftsman Mdl. 103-22920 3” x 7” Horizontal Bandsaw, single phase

Sears Craftsman 10” Rip Saw

10” Bosch Mdl. 4100 Bench Top Table Saw, on cart

 

RADIAL DRILLS & MISCELLANEOUS TYPES OF DRILLS

5’ x 13” Ooya Mdl. RE2-1450A Radial Arm Drill, 12-spindle speeds, 28-1985 RPM, power elevation, tapping, S/N: N77L4491

  • Also Available: 26” x 31” x 48” Long T-Slotted Box Table

 

 

WELDERS

100-KVA Lors Mdl. 1100AP-1 Spot Welder, Interlock 300 Weld Schedule Mdl. 108 microprocessor, cooler, 48” throat, 440v, S/N: 4792449

Craftsman Mdl. 17-076-002 Wire Feeder

 

BENCH TYPE ENGRAVER

Roland Mdl. EGX-300 Bench Type Engraver, S/N: Z404447

 

SHOT BLAST

Econoline 2-Hand Reach-In Shot Blast Cabinet, reclaim canister, 47” left to right x 40” front to back x 47” high approximate inside dimensions, S/N: N/A

 

MISCELLANEOUS

Including: lathe tool posts, c-clamps, Jet bar clamps, numerous Husky rolling tool cabinets, rolling wire racks, hand carts, ladders, Sears 3 ton floor jack, drills, taps, bench vise, pneumatic hand grinders, power tools, drill boxes, large quantity of power tools, 2-door storage cabinets, etc.

 

LAWNMOWERS & POWER GENERATORS

5,000-Watt Husky Mdl. 6250 Generator

4,000-Watt Coleman Mdl. 544000 Generator

Honda Mdl. HT3810 Sit-Down Riding Lawnmower

Craftsman Mdl. Eager-1 3.5HP Push Type Mower, solid state ignition start

 

MISCELLANEOUS EQUIPMENT & SHOP SUPPORT

6’ x 8’ T-Slotted Table

64” Manual Initial Pinch Roll, 3” diameter rolls

98” x 20’ x ¾” Thick Steel Layout Table

36” x 58” x 1-1/2” Thick Steel Layout Table

[2] Southworth “Pallet Pal” 43” Diameter Scissor Material Lifts

Atlas Mdl. MFB Horizontal Mill, single phase, 4-1/2” x 18” table, S/N: 007081

Approximately 2” Pipe Threader

Jet Mdl. DC-1100 1.5HP Single Phase Dust Collector

Sonic Systems Mdl. IB234-8HT Bench Type Sonic Degreaser, 7-1/2” high x 11-1/4” wide x 19” long inside dimensions, S/N: 14123-0397

Paint Spray Booth, 60” deep x 117” wide x 93” high, exhaust

12” Jet Mdl. JDS-12B Bench / Disc Sander, single phase, S/N: 012398

8” Craftsman Mdl. 113-206931 Wood Joiner, S/N: 308C-2014S

7” Dayton Double End Bench Grinder

1/2HP Baldor Double End Pedestal Buffer

Offices, including: HP DesignJet T770 Plotter, HP DesignJet 1050C Plotter, Sharp Copier, Desks, Chairs, File Cabinets

Nine Scale Vacuum Products

Location: 192 Anawan Street, Fall River, MA 02721

Online Bidding Ended:

Auction Highlights

Surplus to the Ongoing Needs of GE Multiple Businesses

Location: Farmington, NM; Richmond, VA; Houston, TX

Online Bidding Ended:

Auction Highlights

Lot Number Description
6 FOLDING CHAIRS & 3′ X 6′ FOLDING TABLE [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
8 PALLET RACKS & PARTS SHELVING [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
12 OLD UTILITY BED [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
19 ALUMINUM FORKLIFT RAMP [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
21 SIDE BOX TOOL BOX [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
24 ELECTRIC HOSE CUTTER [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
25 LARGE FLOOR JACK [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
28 2-5/8″ COMBINATION WRENCH [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
30 NEW 20-GAL. AIR TANK [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
36 3 TON CHAIN HOIST [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
41 1″ – 2″ PIPE CUTTER [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
43 2-GAL. PAINT POT [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
44 LARGE SCALE [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
52 TIRE CHAIN REPAIR TOOL [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
55 1/2″ ELECTRIC DRILL [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
58 LARGE ICE CHEST [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
59 ROLLING CARTS [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
62 BARREL HANDLER & [2] DOLLIES [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
63 [7] ROADSIDE TRIANGLE KITS [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
64 2-WHEEL DOLLY [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
66 GREASE GUNS [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
67 SHACKLES [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
77 NEW RUBBER EXHAUST HOSES [LOCATED AT 3900 BLOOMFIELD HWY, FARMINGTON, NM]
105 PAINT BOOTH, 72″ WIDE X 35″ DEEP X 48″ HIGH, FILTERS IN BACK, DWYER MARK II MDL. 25 MANOMETER (BOOTH ONLY, NO DISKS) [LOCATED AT 16250 PORT NW DRIVE, HOUSTON, TEXAS]
212 AIR QUALITY ENGINEERING GREEN AIR HANDLER, WITH LARGE SUCTION LOCATING ARM [LOCATED AT RICHMOND, VA]
213 AIR QUALITY ENGINEERING GREEN AIR HANDLER, WITH LARGE SUCTION LOCATING ARM [LOCATED AT RICHMOND, VA]
214 AIR FLOW SYSTEMS BLUE AIR HANDLER, WITH LARGE SUCTION LOCATING ARM [LOCATED AT RICHMOND, VA]
215 AIR FLOW SYSTEMS BLUE AIR HANDLER, WITH LARGE SUCTION LOCATING ARM [LOCATED AT RICHMOND, VA]
216 ABATEMENT TECHNOLOGIES MDL. BD2KM HEPA FILTER, S/N: B12816102706 [LOCATED AT RICHMOND, VA]

Surplus to the Ongoing Needs of Multiple General Electric Facilities

Location: Various - Houston, TX; Ft. Worth, TX; Broussard, LA; Erie, PA; New Mexico

Online Bidding Ended:

Auction Highlights

TEXAS, LOUISIANA & NEW MEXICO LOCATIONS

VERTICAL TURNING
84” Giddings & Lewis CNC Vertical Boring Mill, with Siemens 840D CNC controls, S/N: 515-0009-79

Bullard Cutmaster 42” Vertical Turret Lathe, with [1] turret head, [1] ram head, [1] side head, pendant controls, 4.1-150 RPM table speeds (no jaws), S/N: 28467 (1953)

LATHES
Lodge & Shipley Mdl. 2XE-3220-WHD 34” x 120” Geared Head Engine Lathe, with 28” swing over cross slide, 28” diameter 4-jaw chuck, threading attachment, steady rest, Acu-Rite III 2-axis digital readout, 7” hole thru spindle, spindle speeds variable to 900 RPM, S/N: 50326 (1979)

[2] Clausing Mdl. 8056 17” x 110” Geared Head Engine Lathes, with 20-1600 RPM spindle speeds, inch / metric threading (no chuck), S/N’s: 7/0222/13192; 770/222/11814

ROTARY GRINDERS

Blanchard Mdl. 22D-42 Rotary Surface Grinder, with pendant controls, 720 RPM wheel, Neutrofier II, S/N: 15493 (1982)

Bennett Type CG14 Rotary Grinder, with 30” diameter, 1120 RPM grinding wheel speed, DCE Unimaster Mdl. UMA25ZG5AD dust collector (S/N: 93-1017)

CNC HORIZONTAL MACHINING CENTER

Haas Mdl. HS-1 CNC Horizontal Machining Center, with Haas CNC controls, 710 IPM brushless servo, 16” x 16” dual pallet (missing pallets), 24-position automatic tool changer, 20HP vector drive, S/N: 542-0031-34 (1998)

SPRING COILER

BHS-Torin Mdl. 11CNC Programmable Spring Coiler, with hydraulic pump, coiler, Daisy Data controls, wire diameter range .015-.072, coil OD range .093-1.750, pitch tool movement .875 max, acra wire controls feed unit

HORIZONTAL BORING MILL

Giddings & Lewis 5” Horizontal Boring Mill, table type, with 48” x 98” table, outriggers, 78” vertical travel, 120” bed length, 7.5-975 RPM spindle speeds, standard 7.5-467 / high range 480-975, S/N: 150-1141-71

WELDERS

H&H 200-KVA Press Type Spot Welder, 350-amp, 480v, 1PH with chiller, S/N: H5988 (2012)

Tecna Mdl. 3032A 53-KVA Portable Spot Welder, 440v / 3ph, S/N: 008277 (2012)

BOILER

Fulton Mdl. VMP-130LE Boiler, 130HP, 4485#/hr steam, 4.353 MMBTUCH,m complete with feedwater tank system, blowdown tank, S/N: F1018017A (2016)

 

ALSO: MILLING MACHINES · SHOT PEEN · OVEN · PRESSES · INSPECTION

 

PENNSYLVANIA

CNC VERTICAL TURN MILL

Monarch Mdl. TM1250 TAJMAC/ZPS CNC Turn Mill Vertical Turning Lathe, with Siemens Sinumerik control, 4-jaw chuck, 40” x 40” pallet, Technimetal-CZ chip conveyor, 45-position automatic tool changer, Capto C8 tools, 8-position head changer, 55” x-axis, 59” y-axis, z-axis 49.2”, clamping surface diameter 49.2”, 6500 RPM, max number tool heads 10, Rittal chiller, S/N: 08ZP301

TOOL SETTERS

Parlec Type IS6 3200-WK Thermogrip Tool Setter, 85-150 PSI, S/N: 0187 (New 2007)

Parlec Series 1500-PSM Parsetter TMM Tool Setter, S/N: 7A38-060B

DEBURRING UNIT

Ernst Titan Type 1400 Deburring Unit, 55” wider, S/N: 800058 (2011)

LAB EQUIPMENT

Instron Mdl. 3367 Tensile Tester, 30kn capacity, 135kg weight (298#) (2013) [System ID: 3367U2090]

Instron Mdl. E3000 Electro-Plus Fatigue Tester

MSX Mdl. 300R Type 300R1 Abrasive Cutoff Saw, 460v, S/N: 60012 (2003)

Struers Mdl. SECOTOM-50 Digital Abrasive Cutoff Saw, approximately 6” diameter

Leica “Metalgraph” Microscope, with Clemex digital analysis (2015)

Wilson Mdl. VH3100 Hardness Tester, S/N: 733804142 (2014)

Perkin Elmer Mdl. TGA4000 Thermogravimetric Analyzer

Struers Mdl. LECTROPOL-5 Electro Polisher

WELDING & RELATED

Ransome Mdl. 250P-A Welding Positioner, 25,000# capacity, 60” x 60” with 84” sub-table, S/N: 6526215 (1980)

Miller Delta 652 CV/DC Power Source, digital, with Miller 70 Series wire feed, digital & boom

ALSO: TORQUE GUNS · CRANE · MISC. LAB · ETC.

Surplus to the Ongoing Needs of GE Aviation – Multiple Location Sale

Location: Multiple Locations - Clearwater, FL; Newark, DE; Arkansas City, KS

Online Bidding Ended:

Auction Highlights

Wash System:
3-Stage Stainless Steel Pressure Washer, With 4-Stage Digital Control Dryer, 31” X 45” Opening, Hanging Conveyor Drying Racks, Approximately 2000 & 1500-Gal. Water Storage Tanks, Gas Fired (Located: Clearwater, FL)

Roto-Finish:
Roto-Finish Mdl. 5173 Extended Range Series Spiratron Vibratory Finishing Mill, rubber lined, approximately 5’ diameter, S/N: ER-1011C-99-E9 (Located: Clearwater, FL)

CNC Vertical Mill:
Okuma & Howa Mdl. MILLAC4VAC CNC Vertical Machining Center, with 18” x 53” table, 24-position automatic tool changer, #40 taper, Fanuc System 11M controls, S/N: 02307 (Located: Clearwater, FL)

CNC Milling Center:
Miyano Mdl. TSV-33 CNC Drilling & Tapping Machine (Milling Center), with 12-position turret, [2] 12” x 19-1/2” drilled transfer tables, assorted BT-30 taper tool holders, Fanuc O-M controls, S/N: TSV330126 (Located: Clearwater, FL)

CNC Surface Grinder:
Rosa Mdl. IRON12.6 19.75” x 47.25” CNC Surface Grinder, with 19.75” x 47.25” permanent magnetic chuck, CNC wheel dresser, coolant, 10HP spindle speeds to 1500 RPM, Rosa CNC controls, S/N: 04031827 (2008) (Located: Clearwater, FL)

Presses:
Komatsu Mdl. OBS-60 60 Ton Hydraulic Straight Side Punch Press, with 21-1/2” x 30” bed area, air clutch, S/N: 10626 (Located: Clearwater, FL)

Komatsu Mdl. OBS-35 35 Ton Hydraulic Straight Side Press, with 15” x 23-1/2” bed area, air clutch, 100 SPM, 3.15” stroke, 8.27” die height, S/N: 204201 (Located: Clearwater, FL)

Danly 75 Ton OBI Punch Press, with air clutch, 4” stroke, 15-1/2” shut height, 3” adjustment, 40 SPM, 3” bolster plate, S/N: 7555950168 (Located: Clearwater, FL)

Perkins 10 Ton Straight Side Bench Type Punch Press & Table (Located: Clearwater, FL)

Press Brake:
Chicago Mdl. 68-B 8’ x 36-55 Ton Mechanical Press Brake, with motorized ram adjustment, manual back gage, Shadow V light curtain, S/N: L-14037 (Located: Clearwater, FL)

Lathes:
Hardinge Mdl. HLV-H Toolroom Lathe, with quick collet closer, 4-way tool post, motorized carriage feed, spindle speeds to 3000 RPM, S/N: HLV-H-6817-P (Located: Clearwater, FL)

DoAll Romi Mdl. LT16 16” x 80” Geared Head Engine Lathe, Complete with Spindle Grinder, Tracer Attachment, 3-PH/60HZ, S/N: 002-080910-193 (1996) (Located In Newark, DE)

Mills (All Types):
Bridgeport Series I 2HP Vertical Milling Machine, with 9” x 42” power feed table, spindle speeds to 4200 RPM, vise, Acu-Rite digital readout, S/N: 12BR-187089 (Located: Clearwater, FL)

Dehoff Nichols Horizontal Milling Machine, with 8-1/2” x 30” table, pneumatic feed on table, 3HP, vise, S/N: 86018N (Located: Clearwater, FL)

Surface Grinder:
Reid Rayscott Mdl. 618HR 6” x 18” Hand Feed Surface Grinder, with 6” x 18” permanent magnetic chuck, S/N: 30133FC (Located: Clearwater, FL)

Spray Arc System:
(2) Praxair Model CoArc 9910 Spray Arc System with Arc Spray Gun, S/N’s: AP970119; AP970120 (2013)

 Spot Welders:
Taylor Winfield Mdl. ERB-12-150 150-KVA Spot Welder, with 18” throat, foot controls, S/N: 17604 (Located: Clearwater, FL)

Thompson Mdl. A-1 75-KVA Spot Welder, with 18” throat, pneumatic ram downfeed, foot controls, Entron welding controls, S/N: 17604 (Located: Clearwater, FL)

Taylor Winfield Type EBB3-8-50 50-KVA Spot Welder, with 9” throat, WTC Mdl. WT500 controller, S/N: 970125 (Located: Clearwater, FL)

Welder:
Lincoln Mdl. CV-305 Approximately 300-Amp Welder, with Lincoln LF-72 wire feeder (Located: Clearwater, FL)

Saws:
DoAll 36” Vertical Bandsaw, with 30” x 30” hydraulic tilting table

Kysor Johnson 20” Vertical Bandsaw, with 24” x 28” tilting table, blade welding attachment, S/N: N/A

Ryobi Mdl. Pro-Tech 9-1/2” Bench Type Vertical Bandsaw

Stone Approximately 32” Cutoff Saw, with pneumatic downfeed, 1-1/2HP motor, short stop electronic motor brake, S/N: 856

Eisle Mdl. MS-11S-420 Approximately 12” Cutoff Saw, with roller infeed conveyor, automatic downfeed, S/N: 00343 (Located: Clearwater, FL)

Bead Milling System:
Union Process Model DMQX-07-MILL Bead Milling System Complete With Removalble Polyurethane Lined Jacketed For Cooling, 304 Stainless Steel Water Cooled Jacket, 304 Ss Media Fill & Product Inlet Port, Discharge Port, Slurry Drain, Stainless Steel Agitator Shaft With Tri-Lobe Cam, Delta-Shaped Disks And Rods, Media Separator, 3-Hp Explosion Proof Motor, Ac Variable Frequency Controller, 5-Gallon Stainles Steel Premix Tank, Thermofisher Model Thermoflex 3500 Chiller, Meets Cooling Capacity Spec Of 7640 Btu/Hr At Minimum 50 Degrees F. Outgoing Fluid Temperature, S/N: 1002-140701 (2014) (Located: Newark, DE)

Crimping Machine:
Amp Mdl. K Bench Type Amp-O-Lectric Crimping Machine, S/N: 145208 (Located: Clearwater, FL)

Air Compressor:
Atlas Copco Model ZR55VSD 75-HP Screw Type Air Comprssor, Water Cooled, 125-PSI, Complete with (2016) Cooling Skid With Dulex Pump, Dual Plate Type Heat Exchangers, Process Side: 20.6 Gpm, Inlet: 114 Degrees Fahrenheit, Outlet: 87 Degrees Fahrenheit, 1.3 Psid, 43.5 Psig Working Psi @ 275,000 Btuh, Cooling Side: 25% Pg / 75% Water, 57.3 Gpm, 85 Degree Fahrenheit Inlet, 95 Degree Fahrenheit Outlet, 8.44 Psid, 43.5 Psig, Complete With (2) 2-Hp Centrifugal Pump Skid Unit, Paddle Type Flow Switch, Nema 4-Control Panel With Full Voltage Magnetic Starters, (20) 304 Stainless Steel Plate Exchanger With Nbr Glueless Gaskets, Asme Stamped Expansion Tank, Maximum Tempature 230 Degrees Fahrenheit @ 150 Psig, 2″ Mpt Ansi B16.3 Aisi 316l Inlet & Outlet Pipe Connections (2012) (Located: Newark, DE)

Furnace:
Carbolite Model Special-CTF 17/600/DV650 Tube Furnace with separate control box and Eurotherm 2416CG temperature controller. For operation on 240 volt, 50/60 Hz, single phase. For use with a 3.75″ OD process tube.  Half of the heating elements are missing. S/N: 21-303337 (2013) (Located In Newark, DE)

Vacuum Pumps:
(6) Oerlikon Leybold WH2500/DV650 RUVAC/DRYVAC Combination Vacuum Pump, Compact Hermetically Sealed Horizontal Dry Rotary Lobe Blower, 380-480 V/50-60-HZ, Water Cooled Motor and Integral Frequency Drive, DRYVAC 650 Peak Performace of 383 CFM with Compact Hermetically Sealed Dry Compression Screw Technology, Complete with Integral Wide Range Motor and Frequency Drive 380-480 V, 50-60-HZ, Direct Water Cooling, 24 VDC Inlet, Rotor and Exhaust Pure Solenoids and Syntrhtic Oil. Accessories Including: Discharge Non-Return VBalve, Ehaust Silencer, Water and Gas Interlock Switches (Some Never Used – As New As 2016) Located in Newark, DE)

 Optical Comparator:
Deltronic Mdl. DH214 14” Optical Comparator, with 5” x 15” table, Deltronic 612R digital readout, S/N: N/A (Located: Clearwater, FL)

Forklift:
Clark Mdl. E0900-90 Electric Forklift Truck (Located In Newark, DE)

Miscellaneous:
Ridgid Mdl. 535 Portable Pipe Threader, with assorted die heads, cutoff, S/N: EAM1-7300J98 (Located: Clearwater, FL)

Pneumatic Can Crusher, with foot controls, approximately 30” stroke (Located: Clearwater, FL)

[2] Pneumatic Can Crushers (Located: Clearwater, FL)

Southworth Mdl. UP-2-90 2,000# Capacity Scissor Lift, with pendant controls, S/N: 109331 (Located: Clearwater, FL)

Southworth 1,000# Capacity Scissor Lift, with foot controls, approximately 30” x 70” sheet capacity (Located: Clearwater, FL)

Southworth 500# Capacity Portable Scissor Lift, approximately 24” x 78” sheet capacity (Located: Clearwater, FL)

Kalamazoo Mdl. 4084 LPM Motor Driven Pallet Wrapper, S/N: 020701 (Located: Clearwater, FL)

Diversitech Mdl. 4X8DD 10HP Portable Downdraft Table, S/N: 520095-1 (Located: Clearwater, FL)

Air Flow Downdraft Table  (Located: Clearwater, FL)

(3) Airflow Systems Model MP04 & MP14-B1-P66 Mist Collectors (Located in Newark, DE)

Pneumatic Automatic Stamping Machine (Located: Clearwater, FL)

Shake-Proof Mdl. 400 Power Screwdriver, S/N: 2862 (Located: Clearwater, FL)

Random Mdl. SB0062 Coil Winder, S/N: MET16466 (Located: Clearwater, FL)

600# Capacity Core Lifter (Located: Clearwater, FL)

[9] 5,000# Capacity Pallet Storage Racks (Located: Clearwater, FL)

AC/DC Transducer Test System, with Keithley Integra Series 2700 Multimeter Data Acquisition System, Ametek controls (Located: Clearwater, FL)

Schunk Ultrasonic (Located: Clearwater, FL)

Allen 2-Spindle 24” Floor Type Drill Press, with 20-3/4” x 26-1/2” table, S/N: 32853 (Located: Clearwater, FL)

Enco 13” Bench Type Drill Press (Located: Clearwater, FL)

Surplus To The Needs of J.C. Cannistraro

Location: Multiple Locations - Stoughton, Watertown, Boston MA

Online Bidding Ended:

Auction Highlights

North Alabama Pipe Corp. Mdl. UW Universal Welder System, approximately 10 years old, for welding weldelets on pipe, consisting of Miller XMY304 CC/CV DC inverter arc welder – digital, S/N: MB160001A, Miller 70 Series Digital Wire Feed Unit, S/N: MB1603624, Hypertherm Powermax 45 plasma welder, weld station, 3-jaw chuck, programmable controls (Located: Watertown, MA)

T-Drill Mdl. ND-54, ¾”-2” capacity, (Finland) (Located: Boston, MA)

Engel Mdl. M-1640, TDF Roll Forming Machine, 7.5HP, 13 station, S/N: 112498-98 (Located: Stoughton, MA)

Ensett Mdl. M800P Rollforming Machine, 5HP, 230 Volts, 60 cycle, 8-station, S/N: 3234-90 (Located: Stoughton, MA)

8-Station Lockformer Machine (Located: Stoughton, MA)

Niagara Power Squaring Shear, Mdl. JL-10, 10’ x ¼”, 24” deep throat, Front Arm Extentions, Squaring Arm, back gage (Located: Stoughton, MA)

20” Jet Mdl. JDP-20MF Floor Type Drill Press, 18” x 16” table, S/N: 11092717-201109 (Located: Boston, MA)

Capco 2-Ton Overhead Bridge Crane, Single Girder, 46’ span, with 2-ton shaw-boy hoist, pendant control, top running on rails, underhung hoist (Located: Boston, MA)

Kone Cranes 2-Ton Overhead Bridge Crane, Single Girder, with 2-ton Kone cranes hoist, span of about 45’, single girder, pendant control, S/N: 1191014 [2008] (Located: Boston, MA)

2-Ton Harrington Hoist, pendant controls, mounted on single girder with electrics, approximately 120’ long with curve. (Located: Watertown, MA)

2-Door Paint Booth (Located: Boston, MA)

Surplus Fabrication & Toolroom Machinery

Location: 17 Irving Avenue Stamford, CT 06902

Online Bidding Ended:

Auction Highlights

CNC TURRET PUNCH
22 Ton LVD-Strippit Mdl. 1250XP CNC Turret Punch, 49.2” x 49.2” work size, (2) auto indexing stations, 2-sheet grippers, 92” x 62” Ball Transfer Table, GE Fanuc series Oi-PB CNC Control, S/N: 076011204 [2003]

*Assorted punches & dies to be sold separately


LASER SYSTEM
2000 Watt LVD “Helius 2513” CNC Laser, shuttle table, 52” x 110” bed, 98” x 49” working area, Fanuc Mdl. C2000 Laser Unit, S/N: L97Z20629, HCF-Lennox chiller, dust collector, GE Fanuc series 16-L CNC control, Machine S/N: 24994 [1998]

 

PRESS BRAKES, INCLUDING CNC
90-Ton x 78-1/2” LVD Mdl. 90BH10 CAD CNC Hydraulic Press Brake, 60-1/2” between housing, operations control pedestal, CNC back gauge, S/N: 25114 [1998]

80-Ton x 98-1/2” LVD-Strippit Mdl. PPS 80.25 Hydraulic Press Brake, 80-1/2” between housing, CNC back gauge, operations control pedestal, S/N: 32846 [2009]

75-Ton x 8’ Di-Acro Mdl. 75-8 Hydraulic Press Brake, 80” between housing, back gauge, power ram adjustment with indicators, dual palm, S/N: 6751180189

14ga x 48” Di-Acro Mdl. 14-48-2 Press Brake, manual back gauge, 36-1/4” between housings, S/N: 6820677161

*Large Assortment of Die Brake Dies including Wilton & LVD


Shears
|77” x 99.4” Amada Mdl. M-2545 Power Shear, (2) Front Supports, front operated power back gauge, squaring arm, S/N: 2501866 [1981]

12ga x 48” Pexto Mdl. 12-4-4L Mechanical Shear, S/N: 67545

16ga x 24” Di-Acro Mdl. 24 “Vari-O-Speed” Power Shear, manual back gauge, 30-150 SPM, S/N: 2059

 

BELT SANDER, WET-TYPE
36” Timesaver Series 3100 Mdl. 3121-13-04 Wet-Type Abrasive Belt Sander, power table adjustment, digital touch control, coolant, S/N: SN31961 [2004]


LATHES, INCLUDING TURRET-TYPE
17” x 60” South Bend “Turnado-17” Lathe, 1580 max RPM, 4-jaw chuck, approximately 2-1/2” spindle bore, camloc spindle, S/N: 67GJ1102

15” x 40” Southbend “Nordic 15” Lathe, gap-bed, inch/mm, camloc spindle, 2000 RPM, approximately 2” spindle bore, S/N: CN-15-701031C94

10” x 20” Southbend Lathe, Catalog # CL187Z, cabinet base, collet closer, S/N: 12869RKX16

Jones & Lamson #4 Turret Lathe, 3-jaw chuck, tool post, 3-jaw chuck, 6-position turret, S/N: 201750

 

MILLING MACHINES, INCLUDING HORIZONTAL-TYPE
Bridgeport “Series 1” 2HP Vari-speed Vertical Mill, 9” x 42” table, 60-4200 RPM, R8 spindle, S/N: 132631

Bridgeport 1-1/2HP Vari-speed Vertical Mill, 9” x 48” table, 60-4200 RPM, R8 spindle, 1-shot lube, S/N: 186283

Bridgeport 1-1/2HP Vari-speed Vertical Mill, 9” x 42” table, 60-4200 RPM, R8 spindle, 1-shot lube, S/N: 147647

1HP Bridgeport 1HP Step-Pulley Head Vertical Mill, 9” x 48” table, Tibon ways, 7” riser block, R8 spindle, 8-spindle speeds, 80-2720 RPM, S/N: 77817

1HP Bridgeport Step-pulley Head Vertical Mill, 9” x 42” table, 8-spindle speeds, 80-2720 RPM, R8 spindle, S/N: 85842

Milwaukee Mdl. 2H Plain Horizontal Mill, 10” x 50” table, overarm supports, S/N: 25-4045

 

CNC LATHE
Okuma Mdl. LC30 Slant Bed CNC Lathe, Apprx 24” swing over ways, 12-position turret, tailstock, chip conveyor, 10” chuck, AS-IS – needs repair, S/N: 56120640 [1981]

 

WELDING DEPARTMENT
60” x 96” Acorn Welding Table

60” x 60” Acorn Welding Table

60” x 72” Welding Table

Assorted Acorn & Acorn Style Clamps & Tooling

Lincoln Tig 300/300 Welder, S/N: AC-811387

Miller XMT350CC/CV – DC Inverter Welder with Miller XR Control Extender Reach Wire Feeder, coolmate 3-cooler, S/N: WG2389

Miller “Syncrowave 250” tig welder, Bernard Cooler Unit, S/N: KE642278

Miller “Dynasty 350” Multi-phase Tig Welder with cooler, S/N: MC400139L

Esab Mdl. 353CV 350 Amp Welder with Mig 2E Wire Feeder, S/N: MA-J037-046

(2) Lincoln “Mobiflex 200-M” Portable Fume Extractors, S/N’s: M0570210005; M0570530045

 

MISCELLANEOUS MACHINERY
Pratt & Whitney Mdl. #1E Jig Borer, 12” x 24” table, power feeds, optics, sliding head, 65-2500 spindle RPM, S/N: 25208

6” x 18” Reid Mdl. 618H Hand Feed Surface Grinder, Walker 6” x 18” permanent magnetic chuck, 1HP direct drive spindle, S/N: 11382

22ga x 36” Pexto Mdl. 381-D Initial Pinch Type Sheet Metal Roller, stand, S/N: 6161

Everett Mdl. 20DM22 – H/D 22” Abrasive Cut-off Saw, 20HP, mitre cut, entry table, S/N: 08-10530

20” Walker Turner Floor Type Drill Press, single phase, S/N: 2-644

3-Spindle 15” Gang Drill, (2) Walker-turner Heads, (1) Rockwell Head, 8’ cast table

#3 Famco Arbor Press, stand

Perkins Mdl. 4K Manual Screw Type Arbor Press, S/N: 21080

36” x 128” x 12” Thick Granite Surface Plate

Diacro Manual Bench-type Brakes & Shears

 

ALSO AVAILABLE: Bridgeport vises, Aloris toolposts, Diacro manual bench type sheet metal shears & brakes, welding curtains, clamps, cabinets, rolling carts, etc.

KII February Consignment Auction Sale

Location: Multiple Locations - Brooklyn, NY

Online Bidding Ended:

Auction Highlights

North American 7-1/2 Ton Capacity Overhead Bridge Crane, Top Running, 55′ Span, 80 FPM, Complete with R&M Hoist with Integral Trolley, 12.5/1P FPM Hoist Speed, 80′ Runway, S/N: 30620 (Located in Brooklyn, NY)

Acco Wright “Speedway” Top Running Approximately 49′ Span, Approximately 75′ Runway, Free-Standing with Uprights and Runway, Approximately 14′ Under Hook, Pendant Controls (Located in Brooklyn, NY)

C.M. GATTI Model S2550 Power Shear, S/N: 2482

Enco 3″ x 48″ Power Roller

DoAll Model 16-2 Vertical Band Saw

Rousselle Model 3-F OBI Press S/N: DFSA-10871

Troyke Model NC-9-B 4th Axis Rotary Table

Caterpillar 4,000 LBS Capacity Forklift Truck

Yale Walk Along Electric Forklift with Charger

Dewalt Model DW744 10″ Table Saw

Craftsman 3-HP 13-Gallon Portable Air Compressor

Central 2-1/2-HP 21-Gallon Portable Air Compressor

Jet Crane Model JHC-75 Portable Shop Crane, S/N: T512081

Pittsburgh 2-Ton Capacity Folding Shop Crane

Scaffold with Deck & Wheels 6′ x 2′ x 6′ High

Scaffold with Deck (No Wheels) 6′ x 2′ x 6′ High

Scaffold Side Kit

(1) Banding Carts

Kaeser Model SK-26 20-HP Skid Packaged Rotary Screw Type Air Compressor

Rockwell Model 3TT BB “Rockwell” Type Hardness Tester, S/N: 1325

Surplus Fabrication Equipment

Location: Oceanside, NY

Online Bidding Ended:

Auction Highlights

Lot Description
1 ELUMATEC MDL. DC 12 DOUBLE CUT MITRE SAW, 3 HP, 106″ LENGTH BETWEEN HEADS, POWER CLAMPING (ON MEZZANINE) S/N: 87148
2 ELUMATEC MDL. 79.15 DOUBLE CUT MITRE SAW, 3 HP, 100″ LENGTH BETWEEN HEADS, PNEUMATIC CLAMPING, MITRING HEAD, (ON MEZZANINE) S/N: 90176
3 SAMSON? INSTRON MDL. 1000 TENSILE TESTER, (ON MEZZANINE), S/N: 2485
4 DEWALT 5HP RADIAL ARM SAW, 3HP, 14″ MDL. 635, S/N:629836
5 10’ WHITNEY-JENSEN HAND BRAKE
6 45 TON PERKINS SINGLE END BACKWHEEL PUNCH PRESS, 2” STROKE, 2-1/2” RAM ADJUSTMENT, 9-1/2” SHUT HEIGHT, 16” X 24” BED, 38” THROAT DEPTH, FOOT SWITCH, S/N: 40240
7 19” POWERMATIC MDL. 81 VERTICAL BANDSAW, 24″ X 24″ TILTING TABLE, BUTT WELDING ATTACHMENT, S/N: 4-24-12
8 10’ X 3/16” CINCINNATI MDL. 1410 POWER SHEAR, FRONT OPERATED POWER BACK GAUGE, 30” BACK GAUGE RANGE, 10’ SQUARING ARM, 2 FRONT SUPPORTS, S/N: 38423
9 BRIDGEPORT “SERIES I” 2HP VERTICAL MILL, 60-4200 RPM, VARIABLE SPEED, 9 X 42” POWER FEED TABLE COMES WITH COMMANDER MULTI-SPINDLE DRILL HEAD, S/N: N/A
10 135 TON X 10’ CINCINNATI SERIES 5X8 AUTO CYCLE PRESS BRAKE, 3” STROKE, POWER RAW ADJUSTMENT, 102″ BETWEEN HOUSINGS, DUAL PALMS, WITH UNI-PUNCHES COMPLETE WITH DIE RAIL, S/N: 39878
11 50 TON PRESSMASTER MDL. 50T E/M TYPE MH-7-22-6-12 H-FRAME HYDRAULIC PRESS, 36″ DISTANCE BETWEEN UPRIGHTS, RALDON ADJUSTABLE SPEED DRIVE, S/N: 0996323631
12 ROCKWELL VARI-SPEED DRILL, 1/4HP, SINGLE PHASE, 300-4700 RPM, 15″ THROAT DEPTH, 14″ X 11″
14 20” JET MDL. JDP-20MF FLOOR TYPE DRILL PRESS, 1-1/2HP, SINGLE PHASE, 16″ X 13-3/4″ TABLE SIZE, S/N: 9020419
15 DOUBLE END PEDESTAL GRINDER, 1/2HP, 6″, 3450 RPM, SINGLE PHASE, MASTERCRAFT
16 25HP INGERSOLL RAND MDL. EP25-ESP ROTARY SCREEN TYPE AIR COMPRESSOR, 125 PSIG, 91 CFM, S/N: AN334OU97293
17 20HP SAILOR BEAL PISTON TYPE AIR COMPRESSOR
18 DRI-AIRE REFRIGERATED COMPRESSED AIR DRYER
18 CONTAINER, 72″ X 224″ INSIDE DIMENSIONS, SIDE DOOR

Surplus Machinery to the Needs of a Vocational-Technical High School

Location: 250 Foundry Street, South Easton, MA 02375

Online Bidding Ended:

Auction Highlights

Lot Description
1 BRIDGEPORT 2HP VERTICAL MILLING MACHINE WITH ACU-RITE 3-AXIS CNC CONTROL, POWER KNEE, WESEL POWER QUILL, 9″ X 42″ SLOTTED POWER FEED TABLE, 1-SHOT LUBE, S/N: 12/BR 204005
2 BRIDGEPORT SERIES 1 – 2HP VERTICAL MILLING MACHINE, 9″ X 48″ SLOTTED POWER FEED TABLE, ACU-RITE III 2-AXIS DRO, S/N: 12/BR 247673
3 BRIDGEPORT SERIES 1 – 2HP VERTICAL MILLING MACHINE, 9″ X 48″ POWER FEED TABLE, ACU-RITE  2-AXIS DRO, S/N: 446740188X
4 BRIDGEPORT SERIES 1 – 2HP VERTICAL MILLING MACHINE, 9″ X 48″ SERVO POWER FEED TABLE, S/N: 252946
5 BRIDGEPORT SERIES 1 – 2HP VERTICAL MILLING MACHINE, 9″ X 48″ SERVO POWER FEED TABLE, NEWALL TOPAZ 2-AXIS DRO, S/N: 12/BR 230885
6 BRIDGEPORT SERIES 1 – 2HP VERTICAL MILLING MACHINE, 9″ X 48″ SERVO POWER FEED TABLE, NEWALL TOPAZ 2-AXIS DRO, S/N: 12/BR 202166
7 BRIDGEPORT VERTICAL MILLING MACHINE (AS-IS) WITH ACU-RITE TYPE M&S 30 HY-YY MOTOR, SPINDLE SPEEDS 60-4200 RPM, S/N: R2E3561
8 NARDINI “MASCOTE” MDL. MS-1440E 14″/18″ X 40″ GAP BED LATHE, INCH/MM THREADING, THREAD DIAL, STOP GAGE, SPINDLE SPEEDS 25-2000 RPM, 2″ HOLE THRU SPINDLE, S/N: 012015018
9 NARDINI “MASCOTE” MDL. MS-1440E 14″/18″ X 40″ GAP BED LATHE, INCH/MM THREADING, THREAD DIAL, STOP GAGE, SPINDLE SPEEDS 25-2000 RPM, 2″ HOLE THRU SPINDLE, S/N: 012015018
10 ENCO MAXIMAT MDL. V13 13″ X 40″ GEARED HEAD ENGINE LATHE, INCH/MM THREADING, THREAD DIAL, DRAW BAR, SPINDLE SPEEDS 30-2500 RPM, S/N: D2PG2-00S
11 ENCO MAXIMAT MDL. V13 13″ X 40″ GEARED HEAD ENGINE LATHE, INCH/MM THREADING, THREAD DIAL, DRAW BAR, SPINDLE SPEEDS 30-2500 RPM, S/N: D2P62-008
12 ENCO MAXIMAT MDL. V13 13″ X 40″ GEARED HEAD ENGINE LATHE, INCH/MM THREADING, THREAD DIAL, DRAW BAR, SPINDLE SPEEDS 30-2500 RPM, S/N: D2PG2010
13 ENCO MAXIMAT MDL. V13 13″ X 40″ GEARED HEAD ENGINE LATHE, INCH/MM THREADING, THREAD DIAL, DRAW BAR, SPINDLE SPEEDS 30-2500 RPM, S/N: D2P F6 F6 009
14 ENCO MAXIMAT MDL. V13 13″ X 40″ GEARED HEAD ENGINE LATHE, INCH/MM THREADING, THREAD DIAL, DRAW BAR, SPINDLE SPEEDS 30-2500 RPM, S/N: D2PF6F6006
15 NARDINI “MASCOTE” MDL. MS-1440 14″/18″ X 40″ GAP BED LATHE, INCH/MM THREADING, THREAD DIAL, MIC STOP NEWALL TOPAZ 2-AXIS DRO, SPINDLE SPEEDS 31.5-2500 RPM,8″ 3-JAW CHUCK, 2″ HOLE THRU SPINDLE, S/N: D3JDS269
16 NARDINI “NODUS” MDL. ND 1540 15″/20″ X 40″ GAP BED LATHE, INCH/MM THREADING, THREAD DIAL, SPINDLE SPEEDS 30-2360 RPM, 10″ 4-JAW CHUCK, 10″ 3-JAW CHUCK, 2″ HOLE THROUGH SPINDLE, S/N: D9KKU 071
17 VICTOR MDL. 1640B PRECISION HIGH-SPEED 16″/22″ X 40″ GAP BED LATHE WITH INCH/MM THREADING, THREAD DIAL, 2″ HOLE THROUGH SPINDLE, NEWALL TOPAZ 2-AXIS DRO, 10″ 3-JAW CHUCK, S/N: N/A
18 HARIG “SUPER 618″ 6″ X 18″ HAND FEED SURFACE GRINDER WITH 6″ X 18” WALKER CERA MAX PERMANENT MAGNETIC CHUCK, COOLANT
19 ACCU-FINISH SERIES III TOOL GRINDER
20 HAAS MDL. VF-OE CNC VERTICAL MACHINING CENTER, TRAVELS X-30″, Y-16″, Z-20″, CAT-40 TAPER SPINDLE, 14″ X 36″ SLOTTED TABLE, HAAS PROGRAMMABLE COOLANT NOZZLE, 20-POS ATC, 20-HP VECTOR DUAL DRIVE WIRED FOR 4TH AXIS, COOLANT, HAAS CNC CONTROLS, `S/N: 18765 (1999)
21 HAAS 4TH AXIS INDEXER, S/N: 505409
22 HAAS SERVO BAR 300 MAGAZINE TYPE BAR FEEDER WITH ASSORTED SIZING TUBES, S/N: 90461 (2001)
23 DAREX 1/3HP, 3-450 RPM, S/N: 144760