Auction Description
NOW ACCEPTING CONSIGNMENTS
CONTACT US TODAY +1.631.454.1766
- No commissions or expenses charged to the seller
- Promote your sale to tens of thousands of proven auction buyers
- Seller can establish acceptable reserves
- A proven method to promote your surplus from one machine to many machines in a major auction event at no cost to you!
Click Submit Listing or Consignment Submission Form to Consign Your Inventory
| 1 | WATER GLYCOL. TEMP 48-70 DEGREES MAXIMUM OPERATING PRESSURE 100 PSI, ¾-HP PUMP, R22 REFRIGERANT, TEMPTEK DIGITAL CONTROLS, S/N: 5-5-6026 (1995) |
| 2 | 4-KW, ¾-HP PROCESS PUMP, 9.6 GPM, 30-PSI, 5,000 CFM CONDENSER, R-22 REFRIGERANT, CONTROLS, S/N: 105158 (2007) |
| 3 | 4-HP COMPRESSOR, 1.5-HP PUMP, 8.5 GPM CHILLED WATER FLOW, S/N: 64862 |
| 4 | 40″ X 40″ MAXIMUM SECTION VOLUME, 40′ RANGE OF SECTION LENGTHS, 1′-1/4″ MAXIMUM DRILLING THINKNESS, 65 FPM POSITIONING SPEED, 1-1/4″ MAXIMUM DRILLING DIAMETER, 3/8″ TO 43-1/2″ POSTIONING STROKE, 90MM/MIN RANGE OF SPINDLE FEED RATE, 16 FPM SPINDLE POSITION SPEED, COMPLETE WITH GE FANUC 210IS|TB 2-AXIS CNC CONTROLS, 40′ TRAVEL, S/N: 28080, (2003) |
| 5 | [4] SHOP FANS [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 6 | [2] PALLETS OF [8] DRUMS OF NEW CIMCOOL COOLANT [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 7 | STEEL STOCK RACK [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 8 | [4] WOOD TOP SHOP BENCHES WITH ELECTRIC BUFFING JACKS [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 9 | LOT OF ASSORTED 2-DOOR STEEL CABINETS, SHELVING, ASSORTED SHOP BENCHES [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 10 | P&H 3000# CAPACITY ELECTRIC HOIST, WITH BRIDGE PENDANT CONTROLS [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 11 | [6] SHOP CARTS [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 12 | APPROXIMATELY [20] SHOP STOOLS [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 13 | ELECTRICAL BUSS DUCT & TAPS [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 14 | PREMIER 1-1/2 TON CHAIN FALL [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 15 | GRANITE TABLE ON BASE [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 16 | MATSUURA MDL. MC-800V CNC VERTICAL MACHINING CENTER, 16.14″ X 45.27″ TABLE, BT40 TAPER SPINDLE, 30-POSITION AUTOMATIC TOOL CHANGER, MATSUURA SYSTEM MXZ YASNAC CNC CONTROLS, S/N: 86035306 (1986) [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 17 | MATSUURA MDL. MC-1000VS2 CNC VERTICAL MACHINING CENTER, 19.7″ X 47.2″ TABLE, BT40 TAPER SPINDLE, 30-POSITION AUTOMATIC TOOL CHANGER, OILMATIC CHILLER, YASNAC CNC CONTROLS, S/N: 86015124 (1986) [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 18 | MATSUURA MDL. MC-760V-DC CNC VERTICAL MACHINING CENTER, DUAL SPINDLE, BT40 TAPER SPINDLE, 16.1″ X 45.3″ TABLE, 24-POSITION AUTOMATIC TOOL CHANGER, OILMATIC OIL CHILLER, FANUC SYSTEM 6M CNC CONTROLS, S/N: 83073375 (1984) [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 19 | MATSUURA MDL. MC560V CNC VERTICAL MACHINING CENTER, 34″ X 14.96″ TABLE, BT40 TAPER SPINDLE, 20-POSITION AUTOMATIC TOOL CHANGER, DAKIN OIL CHILLER, MATSUURA SYSTEM MX3 YASNAC CNC CONTROLS, S/N: 87015756 (1987) [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 20 | MATSUURA MDL. MC-760VZ CNC VERTICAL MACHINING CENTER, 16.1″ X 45.3″ TABLE, BT40 TAPER SPINDLE, 30-POSITION AUTOMATIC TOOL CHANGER, DAKIN AKS 3 OIL CHILLER, SYSTEM M5X YASNAC CNC CONTROLS, S/N: 87015786 (1983) [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 21 | LNS HYDROBAR HYDRAULIC BAR FEED [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 22 | LNS HYDROBAR HYDRAULIC BAR FEED [LOCATED AT 280 HARTFORD AVENUE, NEWINGTON, CT] |
| 23 | OKUMA MDL. MX-45VAE VERTICAL MACHINING CENTER WITH 18.11″ X 39-1/2″ TABLE, TRAVELS: X-30, Y-18.11″, Z-17.71″, 20 POSITION AUTOMATIC TOOL CHANGER, BT-40 TAPER, SPINDLE SPEEDS TO 7,000RPM, TORIT DRYFLO MIST COLLECTOR, AND OSPU100M CONTROLS, S/N: 12122315 |
| 24 | OKUMA MDL. MX-45VAE VERTICAL MACHINING CENTER WITH 18.11″ X 39-1/2″ TABLE, TRAVELS: X-30, Y-18.11″, Z-17.72″, 20 POSITION AUTOMATIC TOOL CHANGER, BT-40 TAPER, SPINDLE SPEEDS TO 7,000RPM, TORIT DRYFLO MIST COLLECTOR, AND OSP7000M CONTROLS, S/N: 09120928 (NO VISES) [LOCATED IN BELLPORT, NY] |
| 25 | OKK MDL. V1 VERTICAL MACHINING CENTER, WITH 16″ X 19-1/2″ DUAL PALLETS, 20-POSITION AUTOMATIC TOOL CHANGER, CAT #40 SPINDLE TAPER, FANUC 21i-M CONTROLS, S/N: 207 – VISES NOT INCLUDED [LOCATED IN BELLPORT, NY] |
| 26 | MATSURA MDL. MC800V VERTICAL MACHINING CENTER WITH 18″ X 46″ TABLE, BT-40 TAPER, 30-POSITION AUTOMATIC TOOL CHANGER, TORIT DRYFLO MIST COLLECTOR, & YASNAC MX3 CONTROLS, S/N: 870606272 – VISES NOT INCLUDED [LOCATED IN BELLPORT, NY] |
| 27 | MATSURA TOOL PRE-SETTER [LOCATED IN BELLPORT, NY] |
| 28 | 30 TON AMADA MDL. 345NCT CNC TURRET PUNCH, 44-STATION TURRET, [2] AUTO INDEXING STATIONS, FANUC P6M CONTROLS, S/N: AK45007 [LOCATED IN BELLPORT, NY] |
| 29 | LIBERTY SYSTEMS NITROGEN GENERATOR MDL. GEN2-2110, 87-145 PSIG, S/N: 16-0502-01 (NEW 2016) [LOCATED IN BELLPORT, NY] |
| 30 | C.I. HAYES 6″ TYPE LAC ELECTRIC BELT FURNACE, 21KW, DART ACCU-SET VARI SPEED CONVEYOR, NITROGEN, HONEYWELL DIGITAL TEMPERATURE CONTROLS, 2100 DEGREE MAXIMUM TEMPERATURE, S/N: 17088 [LOCATED IN BELLPORT, NY] |
| 31 | C.I. HAYES 6″ TYPE LACMB ELECTRIC BELT FURNACE, 21KW, DARTMICRO DRIVE VARI SPEED CONVEYOR, WATLOW DIGITAL TEMPERATURE CONTROLS, 2100 DEGREE MAXIMUM TEMPERATURE, S/N: 16725 [LOCATED IN BELLPORT, NY] |
| 32 | 9″ LINDBERG TYPE 852-A9-BG-C4-D-E3 BELT FURNACE, 49KW, 4-ZONE, VARI-SPEED BELT CONTROL, 1100 DEGREES MAXIMUM TEMPERATURE, S/N: 909707-M7 [LOCATED IN BELLPORT, NY] |
| 33 | BROWN & SHARPE “GAGE 2000″ COORDINATE MEASURING MACHINE WITH 22″ X 29″ DRILLED & TAPPED GRANITE TABLE, APPROXIMATELY 18” Z-AXIS, 500LB CAPACITY, S/N: 0201-1593 [LOCATED IN BELLPORT, NY] |
| 34 | 36″ TIMESAVER MDL. 137-1 HDMW BELT SANDER/GRINDER, WET-TYPE, AIR KNIFE, VARI-SPEED BELT DRIVE, S/N: 24883 [LOCATED IN BELLPORT, NY] |
| 35 | SULLAIR MDL. 3709VBAC S-ENERGY 3700 ROTARY SCREW TYPE AIR COMPRESSOR, 125 PSI, WS TOUCH CONTROLLER, VARIABLE SPEED DRIVE, S/N: 200151009008 [LOCATED IN BELLPORT, NY] |
| 36 | DEMAG MDL. DR110 CRANE, 10 TON CAPACITY, 23″ APPROXIMATE LIFT, 2-SPEED LIFT, 66″ TROLLEY GAGE, [LOCATED IN LOUISVILLE, KY] |
| 37 | BARBER COLMAN MDL. 2-1/2-4 GEAR HOBBER, S/N: 202 [LOCATED IN COPIAGUE, NY] |
| 38 | BARBER COLMAN MDL. 2-1/2-4 GEAR HOBBER, S/N: 89 [LOCATED IN COPIAGUE, NY] |
| 39 | BROTHER MDL. TC-211 CNC DRILLING AND TAPPING MACHINE, 10-POSITION TURRET, S/N: 111765 [LOCATED IN COPIAGUE, NY] |
| 40 | 6″ X 12″ BOYAR SCHULTZ HAND FEED SURFACE GRINDER, ELECTRO-MATIC RECTIFIER, MAGNA-LOCK, ELECTROMAGNETIC CHUCK, S/N: N/A [LOCATED IN COPIAGUE, NY] |
| 41 | FELLOWS #7 HIGH SPEED GEAR SHAPER, S/N: N/A [LOCATED IN COPIAGUE, NY] |
| 42 | GARDNER MDL. 2H20-23 DOUBLE DISC OPPOSED GRINDER, APPROXIMATELY 23″ DIAMETER WHEELS, 20HP, S/N: 425-1 [LOCATED IN COPIAGUE, NY] |
| 43 | GRINDING WHEELS FOR GARDNER DOUBLE DISC GRINDER – NEW [LOCATED IN COPIAGUE, NY] |
| 44 | GLEASON “CONFLEX” GRINDER, S/N: 28677 [LOCATED IN COPIAGUE, NY] |
| 45 | TRAUB A42 SINGLE SPINDLE SWISS SCREW MACHINE, CUT-OFFS, BAR FEED, S/N: A42/5720 [LOCATED IN COPIAGUE, NY] |
| 46 | TRAUB TB60 SINGLE SPINDLE SWISS SCREW MACHINE, CUT-OFFS, BAR FEED, S/N: 3664 [LOCATED IN COPIAGUE, NY] |
| 47 | WAHLI MDL. 90 GEAR HOBBER, S/N: 1008 [LOCATED IN COPIAGUE, NY] |
| 48 | 15″ WALKER TURNER 5-SPINDLE PRODUCTION GANG DRILL, NOTE: GREEN BENCH DRILL NOT INCLUDED [LOCATED IN COPIAGUE, NY] |
| 49 | FELKER 80-BQ WET-SAW VISE [LOCATED IN COPIAGUE, NY] |
| 50 | AMADA MDL. RG100S 8′ PRESS BRAKE, AMADA CONTROL, 100 TON CAPACITY, LASER PRESS BRAKE GUARD, S/N: 102607 (1984) [LOCATED IN PLYMPTON, MA] |
| 51 | AMADA MDL. VIPROS 358 KING II CNC TURRET PUNCH, FANUC SERIES 18-P CNC CONTROL, 30 TON CAPACITY, 58-STATION TURRET, S/N: 35840378 (2000), WITH AMADA MDL. MP1225NJ AUTO ROBOTIC LOAD / UNLOAD SYSTEM, SHEET SIZE 50″ X 72″, YUKEN HYDRAULIC UNIT, 200L CAPACITY, UNIT #U7300E-EP, S/N: 78175003 (2000), STEVE BARBERI CO. MDL. EX5.5 CHILLER, 68,000 BTU, 10-GPM, S/N: 46092100 (2000) [LOCATED IN PLYMPTON, MA] |
| 52 | UNITRON MDL. 7758 MICROSCOPE WITH MICROCODE DIGITAL READOUT [LOCATED AT 2455 SOUTH ROAD (ROUTE 9), POUGHKEEPSIE, NY] |
| 53 | 12″ MITUTOYO MDL. PJ311 OPTICAL COMPARATOR WITH QUADRA-CHEK III, 9-1/2″ X 11-3/4″ TABLE, OPTOEYE-ML, S/N: 70312 [LOCATED AT 2455 SOUTH ROAD (ROUTE 9), POUGHKEEPSIE, NY] |
| 54 | CROWN MDL. 20WTL, 2000# CAPACITY ELECTRIC WALK BEHIND LIFT, 24 VOLT, 154″ REACH, S/N: W-10370, AND CHARGER [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 55 | 40 HP SULLAIR ROTARY SCREW AIR COMPRESSOR, S/N: 003-106215 [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 56 | KALTENBACH NON-FERROUS COLD MITRE SAW [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 57 | KRAMER MDL. E-300 VIBRATORY FINISHER, 27-1/2″ X 9-1/2″ X 10″ DEEP, S/N: 6161 [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 58 | SIP ROTOPTIC-1 ROTARY TABLE WITH OPTICS, S/N: 282 [LOCATED AT 14 ST. NICHOLAS ROAD, WAPPINGER FALLS, |
| 59 | HAAS Servo 300 Model 48A Bar Feed, 3/8″-3-1/8″ Capacity, Up to 48″ Length, 650 LBS Maximum Bar |
| 60 | Avey No. 5 27″ Type BMA-6 Heavy Duty Drill Press, 24-1/2″ x 22″ Table Hand Crank Elevation, 6-Speed, 150-1200 RPM, S/N: 30406 (Located in poughkeepsie NY) |
| 61 | Bridgeport Series II Vertical Milling Machine, 4-HP, #40 Taper Spindle, with Quik Switch II spindle and 12 tool holders (Located in Poughkeepsie, NY) |
| 62 | Deckel/Maho Model MH 500C CNC Vertical Milling Machine, with CNC 432 Controls, Swivel Head, S/N: 55-283 (Located in Poughkeepsie, NY) |
| 63 | TAUMEL MDL. BK-10 ORBITAL RIVETER WITH MDL. NLAEE ATTACHMENT, S/N: UCY-265110 [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 64 | CTD HIGH SPEED SWIVEL MITRE CHOP SAW, 3HP TILTING HEAD, PNEUMATIC DOWNFEED & CLAMPING [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 65 | FRIEDRICH ORBITAL RIVETER [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 66 | BUSCH MDL. RC0025E506.101 VACUUM PUMP, 20 CFM, 15 TORR VACE, 1-1/2HP, S/N: E40006 [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 67 | SIP ROTOPTIC-1 ROTARY TABLE WITH OPTICS, S/N: 282 [LOCATED AT 14 ST. NICHOLAS ROAD, WAPPINGER FALLS, NY] |
| 68 | PRESTO MDL. M366 LIFT, 1000# CAPACITY, 30″ X 32″ PLATFORM, S/N: 39984 [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 69 | VIDMAR 7-DRAWER CABINET, 7″ HIGH X 28″ WIDE – EACH DRAWER [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 70 | MOTREC MDL. E242 ELECTRIC CART, S/N: 1058012 [LOCATED AT 130 SALT POINT TURNPIKE, POUGHKEEPSIE, NY] |
| 71 | HARIG MDL. 618 AUTOMATIC 6″ X 18″ HYDRAULIC SURFACE GRINDER, WITH CERAMAX PERMANENT MAGNETIC CHUCK, POWER TABLE & CROSS FEEDS, ACU-RITE 2-AXIS DIGITAL READOUT WITH LCD DISPLAY, BUILT-IN HYDRAULIC PUMP, HARIG 2HP SPINDLE, CUSTOM WORK AREA GUARD, S/N: N/A [LOCATED IN GREEN ISLAND, NY] |
| 72 | HARIG MDL. 618 HAND FEED 6″ X 18″ SURFACE GRINDER, WITH PERMANENT MAGNETIC CHUCK, ACU-RITE 2-AXIS DIGITAL READOUT WITH LCD DISPLAY, APPROXIMATELY 2HP SPINDLE MOTOR, CUSTOM BUILT WORK AREA GUARD, S/N: N/A [LOCATED IN GREEN ISLAND, NY] |
| 73 | COLLINS THRED-O-MATIC 22A PIPE THREADER, 3-SPEED, CUT-OFF ASSORTED DIE HEAD, MISCELLANEOUS SPARE PARTS, S/N: 11272 [LOCATED IN PEARL RIVER, NJ] |
| 74 | LUBOW MDL. SC-6 WIRE STRAIGHTENER AND CUT-OUT 6′ RUN-OFF, (2) WITH HIGH HATS, S/N: 2 [LOCATED IN PEARL RIVER, NY] |
| 75 | OSTER 502 BOLT AND PIPE THREADER PIPE DIES 1/4″ – 2″ BOLT DIES 3/8 THRU 2″ 2 DIE CHUCKS AND DEBURR TOOL, S/N: HU950 (1959) JUST REPLACE LOCKING JAWS. UPGRADED TO A BIGGER CAPACITY MACHINE. NOT USED FOR PRODUCTION WORK USED AT A JOB SHOP WELL MAINTAINED (LOCATED IN NEW JERSEY) – SELLER CAN LOAD, ITEM CAN BE INSPECTED |
| 76 | CINCINNATI MODEL 5FL12 5/8″ X 12′ HYDRAULIC SQUARING SHEAR, S/N: 37096 (LOCATED IN PENNSYLVANIA) (ITEM CAN BE LOADED / UNDER POWER / CAN BE INSPECTED) |
| 77 | BUILT OCTOBER OF 1944. 16″CW, AKA 18 X 30. THE ACTUAL SWING IS 18.5 INCHES AND THE DISTANCE BETWEEN CENTERS IS 30 INCHES. ORIGINAL PDF MANUAL INCLUDED., S/N: 25808-K (1944) (LOCATED IN PENNSYLVANIA) (UNDER POWER – Y, LOADED – Y, INSPECTED – Y) |
| 78 | REID NO. 2-C 6″ X 18″ MANUAL FEED SURFACE GRINDER, 48″ X 48″ FOOTPRINT (LOCATED IN MASSACHUSETTS) (UNDER POWER – Y, CAN SELLER LOAD – Y, CAN BE INSPECTED – Y) |
| 79 | JACK MILL MACHINE TOOL MFG. CO., LTD MODEL GU-450M CYLINDRICAL GRINDER, SWIVEL TO TABLE 10, MAX WORK RANGE 10 /16 TN, WHEEL SIZE 14 X 1-1/2 X 5, SPINDLE SPEED 1520.1900 RPM, SWIVEL OVER TABLE 0 – 90, TAPER MT-4, MOUNTING STROCK TAPER MT-3 V 220/440, HZ 50 ELECTRICS (LOCATED IN OHIO) (IS ITEM UNDER POWER – Y, CAN ITEM BE LOADED – Y, CAN ITEM BE INSPECTED – Y) |
| 80 | PFAUTER MODEL P120 GEAR HOBBER, EXCELLENT CONDITION WITH A LOT OF TOOLING AND CHANGE GEARS, S/N: 21148 (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 81 | JONES & LAMSON MODEL FC 30 30″ OPTICAL COMPARATOR, EXCELLENT CONDITION, S/N: 22158 (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 82 | EVERETT MODEL 12 MIT COLD SAW, S/N: 1300 (LOCATED IN OHIO) (ITEM IS UNDER POWER – Y, ITEM CAN BE LOADED – Y, ITEM CAN BE INSPECTED) |
| 83 | ACME GRIDLEY, MODEL 2-5/8 RB 6 SCREW MACHINE, ACME GRIDLEY, MODEL 2-5/8 RB 6 SCREW MACHINE (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 84 | ACME GRIDLEY MODEL 9/16 RA 6 SCREW MACHINE, EXCELLENT CONDITION (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 85 | SAJO MODEL PF-54 HORIZONTAL MILLING MACHINE, S/N: 721936 (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 86 | G&E MODEL 36H GEAR HOBBER (VERY GOOD CONDITION) (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 87 | ACME GRIDLEY MODEL 1″ RA 6 SCREW MACHINE, S/N: 124 (EXCELLENT CONDITION) (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 88 | KALAMAZOO MODEL H9AWV HORIZONTAL BANDSAW, S/N: 17916 (VERY GOOD CONDITION) (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 89 | MOTOMAN MODEL MH-1600 WELDING CELL 2 HEADS 2 POSITIONERS COMPLETELY GONE THRUE REBUILT WITH ALL NEW PARTS, HEADS, FEEDERS, SERVOS ECT… BY ROBOTWORKS SPARED NO EXPENSES TO GET THEM WORKING FOR A JOB THEN NEVER USED. S/N: 000513, (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 90 | CLEARING MODEL 110 P 701 OBI PRESS 110 TON PRESS, S/N: 54-3217 RUNS GREAT (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 91 | MILLER MODEL MPS-20 SPOT WELDER, 20-KVA, WITH BASE, S/N: JD669637 NEW CONDITION MILLER MODEL MPS-20 SPOT WELDER |
| 92 | JOHNFORD MODEL SL-500A 6 AXIS CNC LATHE WITH SUB-SPINDLE, LIVE TOOLING, 12′ BAR FEEDER, COLLETS & CHUCKS, LOTS OF NEW TOOLING, COST WAS OVER $300,000.00 NEW, 200 HRS OF USE, S/N: TEN186199 (2019) WE LOST CONTRACT IT IS LESS THAN A YEAR OLD (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
| 93 | JOHNFORD MODEL SL-500A 6 AXIS CNC LATHE WITH SUB-SPINDLE, LIVE TOOLING, 12′ BAR FEEDER, COLLETS & CHUCKS, LOTS OF NEW TOOLING, COST WAS OVER $300,000.00 NEW, 200 HRS OF USE, S/N: TEN186199 (2019) WE LOST CONTRACT IT IS LESS THAN A YEAR OLD (LOCATED IN OHIO) (ITEM UNDER POWER – Y, ITEM BE LOADED – Y, ITEM BE INSPECTED – Y) |
